Dynapac CA3500DCP Page 63 Instruction Manual Download

Page: 63 / 178

Machine description

4812165301.pdf

2022-09-02

"ADJUSTMENTS"

"TESTMODES" - Installation personnel only, requires
pin code.

"CALIBRATION"

- service personnel only, requires

password.

"EDC Calibration" used to calibrate the joystick and
speed potentiometer.

"TX Program" only used to change software in the
display and requires special equipment and know-how.

"EDC CALIBRATION"

To calibrate, move the joystick fully forward (F) and
press in both black buttons on the top of the joystick.
(See also manual W3025)

Continue in the same way with the other positions for
the joystick (N), (R) and the speed potentiometer.

Press the disk button to save the values.

"ABOUT"

It is also possible to see the version of the installed
software.

Summary of Contents for CA3500DCP



















































































































































































Search results

Summary of Contents for CA3500DCP

Reviews:

Related manuals for CA3500DCP

Brands by name

Popular brands

Dynapac CA3500DCP, Instruction Manual

Search results

Summary of Contents for CA3500DCP

Reviews:

Related manuals for CA3500DCP

Brands by name

Popular brands