21. ALARM CH ON/OFF PAGE
The Superior Speed Dome has four alarm inputs, which
can be programmed as 1 second to 180 seconds priority.
When an alarm is received, an input signal to the dome
triggers the user-defined action (go to presets)
programmed for the alarm.
There is resume alarm setting:
RESUME - This mode lets the dome resume its
previous activity (swing, group-tour, auto-tour, or
previous position) after all alarms are cleared.
ALARM CHANNEL
There are two settings:
ON - Activate alarm input.
OFF (default) - Inactivate alarm input.
Use the following steps to program alarm settings:
Use the joystick to position the cursor beside Alarm
CH on/off page. Move the joystick left or right to enter.
Use the joystick up or down to position the cursor
beside each menu in the alarm channel on/off page.
Move the joystick left or right to be ON in each
relative channel. If the set to ON, the channel is
programmed.
ALARM REALY
This function allows user want to disable alarm output,
even if alarm input ready to activate.
There are two settings:
OFF (default) - Disable alarm output by force against
activated input signals.
ON - Enable alarm output when input signal activate.
RESUME TIME SET
It allows revert to previous position (Swig, Group, Tour,
etc) after alarm active.
Select the alarm priority:
Use the joystick to position the cursor beside
RESUME TIME SET.
Move the joystick left or right to set to:
OFF (default), 001 second to 180 seconds.
For reverting sequence functions, this resume time set
allows the dome reverts to
'
Swing
' '
Group-tour
'
, and
'
Auto tour
'
, regardless alarm acfive.
The following is the steps:
Define
'
Resume Time Set
'
as desire on the OSD
menu.
Exit OSD menu after set.
Execute Group-tour or Auto-tour or Swing with the
dedicate keyboard controller as desire.
Then your dome executes
'
GROUP
'
or
'
TOUR
'
after
defined set time, even if other person operates to
other functions.
To escape this function, it must be pushed a
sequence button on the keyboard that is executed at
the present again, e.g.
,
,
button.
ACTIVE ALARM
Active Alarm allows choose to alarm sensor type:
OPEN or CLOSE.
The default is OPEN.
<< CAMERA SETUP p3 >>
17. Select Alarm
: Sensor
18. Motion on/off
: Off
19. Motion Detection Set :
20. PRIVACY ZONE SET :
21. ALARM CH ON/OFF PAGE
22. ALARM PRESET SET PAGE
23. FACTORY RESET WARNING!
- PREV MENU PAGE
<< ALARM CHANNEL ON/OFF >>
- Alarm channel-1
: OFF
- Alarm channel-2
: OFF
- Alarm channel-3
: OFF
- Alarm channel-4
: OFF
- Alarm RELAY
: OFF
- Active Alarm
: OPEN
- Resume Time Set : OFF
- PREV MENU PAGE
<< ALARM CHANNEL ON/OFF >>
- Alarm channel-1
: OFF
- Alarm channel-2
: OFF
- Alarm channel-3
: OFF
- Alarm channel-4
: OFF
- Alarm RELAY
: OFF
- Active Alarm
: OPEN
- Resume Time Set : OFF
- PREV MENU PAGE
Note : Normally, there are two kind of sensor. One
is open type sensor and other is close type
sensor. e.g. PIR sensor is OPEN type
sensor.
<< ALARM CHANNEL ON/OFF >>
- Alarm channel-1 : OFF
- Alarm channel-2
: OFF
- Alarm channel-3
: OFF
- Alarm channel-4
: OFF
- Alarm RELAY
: OFF
- Active Alarm
: OPEN
- Resume Time Set : OFF
- PREV MENU PAGE
<< ALARM CHANNEL ON/OFF >>
- Alarm channel-1
: OFF
- Alarm channel-2
: OFF
- Alarm channel-3
: OFF
- Alarm channel-4
: OFF
- Alarm RELAY
: OFF
- Active Alarm
: OPEN
- Resume Time Set : OFF
- PREV MENU PAGE