background image

 

 

20 

Dymax BlueWave® LED Flood System User Guide 

3.

 

Press and release the  

 Button to enter the Options Menu (Figure 21).  

4.

 

Use 

 or 

 

Arrows so that “ADJUST TIMER” is flashing

 and press the 

 Button. 

5.

 

The Adjust Timer Screen (Figure 22) will display. Use the Directional Keys to adjust the Timer to the 
correct value.  The Timer can be adjusted from 0000.0 seconds to 9999.9 seconds. Press and release the 

 Button when you have entered the desired activation time. 

Figure 20. Time Mode 
Main Screen 

 

Figure 21. Options Menu 
 

 

Figure 22. Adjust Timer 
Screen 

 

 

6.

 

Press the Foot Switch or the 

 Button on the front panel to start the Timer.  An exposure cycle can 

be cancelled at any time by momentarily pressing the 

 Button or Foot Switch.  

Operating in PLC Mode 

PLC Mode Description  

CAUTION!

  

Always wear protective goggles or a face shield when working near UV light. The 

PLC is capable of turning on the LED at any time, or when a user selects PLC Mode from the front 
panel controls. 

PRÉCAUTIONS!

 Veuillez toujours porter des lunettes protectrices pour les yeux ou pour le 

visage lors de travail en contact avec la lumière UV. Le 'PLC' peut mettre sous tension le système 
DEL en tout temps, ou lorsque l'utilisateur sélectionne le mode 'PLC' avec les commandes du 
panneau frontal. 

PLC Mode

 

means that an external PLC (Programmable Logic Controller) controls the system. The PLC provides 

input signals to the flood unit to control the LED. The PLC monitors the status of the flood unit by reading 
output signals provided by the unit. The PLC is typically programmed to start other machinery when the flood 
unit becomes ready, or perhaps start the flood unit when other machinery is ready.  The input signals and 
output signals are present on a connector on the back of the power supply labeled 

‘PLC’

NOTE

: Output signals are always provided in manual mode and timer mode to allow simple interfacing to 

alarms, counters, other interlocks, etc. even if a PLC will not be controlling the unit. However, the input signals 
will be ignored in manual mode and timer mode.

 

Summary of Contents for 41260

































Reviews: