background image

- 26  - 

DXE-T001  -  DX Engineering SO-239 Connector Installation Tool Kit 

This DX Engineering SO-239 connector installation tool kit offers an easier installation of chassis or bulkhead mount SO-239 coaxial 
connectors. Having the right tools can make all of the difference in your shack, and this handy DXE tool 
provides you with a special dual-use stainless steel wrench, plus a multipurpose 6-in-1 screwdriver/nut 
driver tool. One end of the wrench is a 3/4 in. semi-box wrench with a pass-through for coaxial cable--
perfect for tightening the larger nuts used to mount bulkhead connectors. The other end is a 3/16 in. box 
wrench for tightening mounting nuts with SO-239 hardware. You'll receive six combinations - two Phillips 
heads, two flatheads, and a 1/4 in. nut driver and a 5/16 in. nut driver, which store in the handle of the 
screwdriver. The added SO-239 wrench is ideal for use with the 

DXE-UHF-FDFB-KIT

  -  Silver Plated 

Female SecureMount

 Bulkhead Connector.

 

 
DXE-FP-WIRE-P  -  Feedpoint Wire and Connector Assembly 

DX Engineering Feedpoint Wire and Connector Assemblies provide a new and unique method of feeding an antenna radiating 
element. A ring terminal with a 1/4 in. hole is crimped and soldered to a 12 in. long insulated 14 AWG stranded 
copper wire, with weather-protective heat shrink tubing. The Feedpoint wire is terminated to the center pin of a 
UHF male PL-259 with special insulating sleeves and weather-sealing heat shrink. This assembly is intended to be 
used with a double female bulkhead connector, mounted into the Radial Plate, for use on an HF vertical antenna. 
The wire and connector combination allows for the complete weather sealing of a single wire feedpoint, while 
properly terminating the feedline shield to the radial system or ground point of the antenna system. 

 
DXE-RADW  - 500K or 1000K  Radial Wire Kits and Components

 

To achieve optimal performance with a ground-mounted vertical, install as many radials as possible. These bulk 
radial wire kits use insulated wire that is UV resistant, hard to see and lays down easily, unlike the wire that is 
commonly available at the big box stores. It will last much longer in contact with soil than bare wire. 
The DXE-RADW- 500K or 1000K kit provide everything you will need to build the perfect radial system!  

 

500/1000 ft. spool of 14 AWG, stranded copper wire with vinyl insulation  

 

20/40 lugs  

 

100/200 radial wire anchor pins-  Eliminating the need to bury your radials!  

 

Build up to 20/40 radials, 25 feet long 

 

DXE-RADW-500K 

Bulk Radial Wire Kit, 500 ft Spool of Wire, 20 Lugs, 100 Staples 

DXE-RADW-1000K 

Bulk Radial Wire Kit, 1000 ft Spool of Wire, 40 Lugs, 200 Staples 

 
TES-2155

 - 

3M Temflex™ 2155 Rubber Splicing Tape

   

Conformable self-fusing rubber electrical insulating tape.  It is designed for low voltage electrical insulating and moisture 
sealing applications.  For outdoor use, it should be protected from UV deterioration with an overwrap of

 

TES-06132.

 

 
TES-06132 - Scotch

®

 Super 33+

   

Highly conformable super stretchy tape for all weather applications.  This tape provides flexibility and easy handling for all 
around performance.  It also combines PVC backing with excellent electrical insulating properties to provide primary 
electrical insulation for splices up to 600V and protective jacketing. Both tape products are available from DX Engineering. 

 
DXE-RADW-20RT/-32RT/-65RT Pre-Assembled, Radial Wire, w/ 1/4" ring Terminals, 20 Pack

 

The DXE-RADW Radial Wire Kits include the highest quality 14 gauge stranded copper wire with a relaxed black PVC insulation 
for easy installation of your radial system.  They allow fast and easy installation of your radial ground system, and permit you to mix 
and match different length to fit the available space. The stranded wire and relaxed insulation mean that the wire will lay flat as you 
place it on the ground - easy to install! The twenty pre-cut radial wires include 1/4" ring terminals 
professionally crimped on one end for quick and easy attachment to the radial plate.  These Radial Wire Kits 
are designed for users of vertical antenna systems which have the need for a high quality radial system for 
optimum antenna performance. The 1/4" ring terminals are machine crimped for maximum grip.  Soldering is 
not required for strength, but is recommended if installed in corrosive environments such as salt spray. 

 

Packed 20 Radial Wires per package 

 

14 gage, stranded copper wire  

 

Black relaxed PVC insulation 

 

1/4" Ring Terminal professionally crimped on each Radial Wire 

 

3 lengths to choose from: 20 Ft (-20RT), 32 Ft (-32RT), 65 Ft (-65RT)  

 
 
 
 
 

 

DXE-RADW-20RT 

Package of 20 each 20 Ft Radials with 1/4" Ring Terminals 

DXE-RADW-32RT 

Package of 20 each 32 Ft Radials with 1/4" Ring Terminals 

DXE-RADW-65RT 

Package of 20 each 65 Ft Radials with 1/4" Ring Terminals 

Summary of Contents for DXE-4030VA-1





























Reviews: