- 27 -
DXE-STPL - Radial Wire Anchor Pins, 100/pack - No need to bury your radials!
DX Engineering Radial Wire Anchor Pins are perfect for fastening radials below the grass line to eliminate the risk of damaging your
radials during lawn maintenance.
100 count - 6'' Pins
11-Gauge
DXE-STPL-100P
Radial Wire Anchor Pins, 100/pack
DXE-STPL-300P
Radial Wire Anchor Pins, 300/pack
SUM-900031 - Automatic Wire Stripper/Crimper/Cutter, 24-10 Ga.
Our DX Engineering wire stripper uses a spring-loaded design to make quick work of wires ranging from 24 to 10 gauge. Just insert
the wire, squeeze the handle, and listen for the click. That’s the sound of another perfect wire stripping job performed
in about 2 seconds- a fraction of the time it takes your pocket knife to do the same job. An adjustable wire length guide
helps you make uniform strips, and a built-in wire cutter and crimper helps you complete your wiring job.
Spring-loaded design
Strips wires ranging from 24 to 10 gauge
built-in wire cutter and crimper
DXE-GUY-Kits - Guying Kit for Vertical Antennas
Some vertical manufacturers indicate their antennas do not need guying. During times of high winds or ice loading,
some of these verticals may sustain damage or fail altogether. With the small amount of effort needed to install a four
point guying system, the risk hardly seems worth taking. A four-point guying scheme provides the best mechanical
advantage to reduce wind stress, regardless of direction. A four point guying system is recommended for use with a
DX Engineering Tilt Base, because just one of the guy ropes has to be loosened when you tilt the vertical down. The
remaining guys help stabilize the vertical in three directions when being raised. These Vertical Guying kits have been
designed to be used with ground mounted vertical antenna systems. The guying kits are ideal for fixed or portable
installations.
DXE-GUY100-KIT
4 - Heavy Duty screw-in earth anchors with eyelets
1 - 100 ft Roll - UV resistant, 3/32 Double-Braided Dacron Polyester Rope SYN-DBR-94-100
DXE-GUY200-KIT
4 - Heavy Duty screw-in earth anchors with eyelets
2 - 100 ft Rolls - UV resistant, 3/32 Double-Braided Dacron Polyester Rope SYN-DBR-94-100
DXE-GUY400-KIT
4 - Heavy Duty screw-in earth anchors with eyelets
4 - 100 ft Rolls - UV resistant, 3/32 Double-Braided Dacron Polyester Rope SYN-DBR-94-100
DXE-GUY1000-KIT
4 - Heavy Duty screw-in earth anchors with eyelets
1 - 1000 ft Roll - UV resistant, 3/32 Double-Braided Dacron Polyester Rope SYN-DBR-94-1000
Technical Support
If you have questions about this product, or if you experience difficulties during the installation, contact DX
Engineering at (330) 572-3200. You can also e-mail us at:
For best service, please take a few minutes to review this manual before you call.
Warranty
All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a period of one (1) year from date of shipment. DX
Engineering’s sole obligation under these warranties shall be to issue credit, repair or replace any item or part thereof which is proved to be other than as warranted; no
allowance shall be made for any labor charges of Buyer for replacement of parts, adjustment or repairs, or any other work, unless such charges are authorized in advance by
DX Engineering. If DX Engineering’s products are claimed to be defective in material or workmanship, DX Engineering shall, upon prompt notice thereof, issue shipping
instructions for return to DX Engineering (transportation-charges prepaid by Buyer). Every such claim for breach of these warranties shall be deemed to be waived by
Buyer unless made in writing. The above warranties shall not extend to any products or parts thereof which have been subjected to any misuse or neglect, damaged by
accident, rendered defective by reason of improper installation, damaged from severe weather including floods, or abnormal environmental conditions such as prolonged
exposure to corrosives or power surges, or by the performance of repairs or alterations outside of our plant, and shall not apply to any goods or parts thereof furnished by
Buyer or acquired from others at Buyer’s specifications. In addition, DX Engineering’s warranties do not extend to other equipment and parts manufactured by others
except to the extent of the original manufacturer’s warranty to DX Engineering. The obligations under the foregoing warranties are limited to the precise terms thereof.
These warranties provide exclusive remedies, expressly in lieu of all other remedies including claims for special or consequential damages. SELLER NEITHER MAKES
NOR ASSUMES ANY OTHER WARRANTY WHATSOEVER, WHETHER EXPRESS, STATUTORY, OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME FOR DX ENGINEERING ANY OBLIGATION OR LIABILITY NOT
STRICTLY IN ACCORDANCE WITH THE FOREGOING.
©DX Engineering 2017
DX Engineering
®
, DXE
®
, DX Engineering, Inc.
®
, Hot Rodz
®
, Maxi-Core
®
, DX Engineering THUNDERBOLT
®
, DX Engineering Yagi Mechanical
®
, EZ-BUILD
®
,
TELREX
®
, Gorilla Grip
®
Stainless Steel Boom Clamps, Butternut
®
, SkyHawk™, SkyLark™, SecureMount™, OMNI-
TILT
™, RF-PRO-1B
®
, AFHD-4
®
are trademarks of
PDS Electronics, Inc. No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other brands and product names are the
trademarks of their respective owners.
Specifications subject to change without notice.
