DuroStar DUROMAX DUAL FUEL XP8500EH User Manual Download

Page: 79 / 84

maintenance listed in your owner’s manual. DuroMax Power Equipment recommends that you

retain all receipts covering maintenance on your small off-road engine, but DuroMax Power

Equipment cannot deny warranty solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.

As the small off-road engine owner, you should, however, be aware that DuroMax Power
Equipment may deny you warranty coverage if your small off-road engine or a part has failed due
to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your small off-road engine to a DuroMax Power Equipment

distribution center as soon as a problem exists. The warranty repairs should be completed in a
reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, contact DuroMax
Power Equipment authorized warranty service facility:

TEL: 1-844-387-6629
WEBSITE: www.duromaxpower.com
ADDRESS: 5800 Ontario Mills Pkwy, Ontario CA 91764

This telephone number is only for the engines which the company name “DuroMax Power
Equipment” on the emission label.

DEFECTS WARRANTY REQUIREMENTS:

(a) The warranty period begins on the date the engine or equipment is delivered to an ultimate

purchaser.

(b) General Emissions Warranty Coverage. DuroMax Power Equipment warrants to the ultimate

purchaser and each subsequent owner that the engine or equipment is:

(1) Designed, built, and equipped so as to conform with all applicable regulations adopted by

US EPA & Air Resources Board; and

(2) Free from defects in materials and workmanship that causes the failure of a warranted

part for a period of two years.

(1) Any warranted part that is not scheduled for replacement as required maintenance in

the written instructions required by subsection (d) must be warranted for the warranty

period defined in Subsection(b)(2). If any such part fails during the period of warranty

coverage, it must be repaired or replaced by DuroMax Power Equipment according to

Summary of Contents for DUROMAX DUAL FUEL XP8500EH





















































































Search results

Summary of Contents for DUROMAX DUAL FUEL XP8500EH

Reviews:

Related manuals for DUROMAX DUAL FUEL XP8500EH

Brands by name

Popular brands

DuroStar DUROMAX DUAL FUEL XP8500EH, User Manual

Search results

Summary of Contents for DUROMAX DUAL FUEL XP8500EH

Reviews:

Related manuals for DUROMAX DUAL FUEL XP8500EH

Brands by name

Popular brands