![background image](http://html1.mh-extra.com/html/ducati/multistrada-1200/multistrada-1200_owners-manual_2537805237.webp)
With fixed drilled steel disc.
Disc diameter: 245 mm.
Hydraulically operated by a pedal on RH side.
Make: BREMBO
Type: P34c pistons.
Friction material: FERIT I/D 450 FF.
Master cylinder type: PS 13c.
Warning
Brake fluid can dissolve paintwork.
In the event of accidental contact with eyes or skin,
wash the affected area with abundant running water.
Transmission
Wet clutch controlled by the lever on left-hand side
of the handlebar.
Drive is transmitted from engine to gearbox main
shaft via spur gears.
Engine sprocket/clutch gearwheel ratio: 33/61
6-speed gearbox with constant mesh gears, gear
change pedal on left side of motorcycle.
Gearbox output sprocket/rear chain sprocket ratio:
15/40
Total gear ratios:
1
st
gear 15/37
2
nd
gear 17/30
3
rd
gear 20/27
4
th
gear 22/24
5
th
gear 24/23
6
th
gear 25/22
Drive chain from gearbox to rear wheel:.
Make: REGINA
Type: 136ZRPB
Size: 5/8” x 1/16”
Links: 108
Important
The above gear ratios are the homologated ones
and under no circumstances must they be modified.
However, if you wish to tune up your motorcycle for
competitions or special tracks, Ducati Motor Holding
S.p.A. will be pleased to provide information about
the special ratios available. Contact a Ducati Dealer or
Authorised Service Centre.
236
Summary of Contents for Multistrada 1200
