DSC Power608 Installation Manual Download Page 21

Page: 21 / 52

P r o g r a m D e s c r i p t i o n s :

5 . 6 C o m m u n i c a t o r – A c c o u n t N u m b e r s

5.6

Communicator – Account Numbers

The account number is used by the central station to distin-
guish between panels. There are two account numbers pro-
grammable for the PC5008.

First Account Code (4 digits) . . . . . . . . . . . . . . Section [310]
Second Account Code (4 digits) . . . . . . . . . . . Section [311]

5.7

Communicator – Telephone Numbers

The panel can use three different telephone numbers for com-
municating with the central station. The

First Telephone

Number

is the primary number, the

Second Telephone Num-

ber

is the secondary number and the

Third Telephone Num-

ber

will back up the First telephone number if enabled.

NOTE: The Third Telephone Number will NOT back up the
Second Telephone Number.

NOTE: If you enter a telephone number section (sections [301]
- [303]) at an LED keypad, pressing [#] will delete the pro-
grammed telephone number and change all the digits to [F].

If the

Alternate Dial

option is enabled, the panel will alternate

between the first and third telephone numbers when attempt-
ing to call the central station. If the option is disabled, the
panel will only attempt to call the Third telephone number after
failing to communicate with the first telephone number.

NOTE: To use the Third Telephone Number, you must enable it
in section [380], option [5], and program it in section [303].

Telephone numbers can be up to 32 digits. This allows you to
add special digits if required. To program the telephone number,
enter the numbers 0 through 9 as required. The following is a list
of programmable HEX digits and the functions they perform:
HEX (B) - simulates the [*] key on a touch tone telephone
HEX (C) - simulates the [#] key on a touch tone telephone
HEX (D) - forces the panel to search for dial tone
HEX (E) - forces the panel to pause for 2 seconds
HEX (F) - marks the end of the telephone number

Two-way Voice Monitoring

The PC5928 module has built-in two-way voice for central sta-
tion monitoring. The central station can select the audio sta-
tion, listen/talk, extend on-line time and hang up. The

Listen-

feature can be enabled separately for telephone numbers

1/3 and 2.

NOTE:The first digit of all telephone numbers must be the HEX
digit ‘D’ for dial tone search, or HEX digit ‘E’ for a two-second
pause.

First Telephone Number . . . . . . . . . . . . . . . . . .  Section [301]
Second Telephone Number . . . . . . . . . . . . . . .  Section [302]
Third Telephone Number . . . . . . . . . . . . . . . . .  Section [303]
Third Telephone Number Enable . . . . . . . .  Section [380]: [5]
Alternate Dial  . . . . . . . . . . . . . . . . . . . . . . .  Section [380]: [6]
Telephone # 1 & 3 Listen-In Enable . . . . . .  Section [381]: [5]
Telephone # 2 Listen-In Enable  . . . . . . . . .  Section [381]: [6]

5.8

Communicator – Reporting Codes

The panel can be programmed to report events to the central
station by sending the Reporting Code programmed for a par-
ticular event.
Reporting codes can be one or two digits and can use HEX
digits (A through F). For a complete description of reporting

codes which can be programmed and lists of automatic Con-
tact ID and SIA format codes, please see Appendix A.

NOTE:Do not use the digit C in a reporting code when using
Pager Format. In most cases, the digit C will be interpreted as
a [#] which will terminate the page before it has finished.

Reporting Codes . . . . . . . . . . . . . . . . . Section [320] to [353]

Cross Zone Police Reporting Code

The

Cross Zone Police Code Alarm

will be sent when two

different alarms occur during any armed-to-armed period.
When an alarm occurs while the panel is armed and a second
alarm occurs on a different zone during the same armed
period, or after the system is disarmed, this code will be sent.
All zone types contribute to this alarm. The cross zone police
code will be transmitted immediately unless either or both
zones have the Transmission Delay attribute enabled. If so,
the code will be delayed for the programmed transmission
delay time.

Cross Zone Police Code Alarm . . . . . . . . . . . . Section [328]

Zone Restorals

If the

Restoral on Bell Time-out

option is selected, the panel

will send the

Zone Restoral Reporting Code

for the zone if

the bell cut-off time has expired and the zone is secured. If the
zone is not secured when the bell cut-off time expires, the
panel will send the restoral immediately once the zone is
secured, or when the system is disarmed. If the Restoral on
Bell Time-out option is not selected, the panel will immediately
send the Zone Restoral Reporting Code when the zone is
secured, regardless of whether or not the alarm output is
active.

NOTE:24 Hour type zones will report the restoral immediately
when the zone is secured.

Restoral on Bell Time-out. . . . . . . . . . . . . . .Section [380]: [2]

Closings (Arming Codes)

If the

Closing Confirmation

option is enabled, once the exit

delay expires, the keypad will sound a series of eight beeps to
confirm to the user that the closing code was sent and
received by the central station.
The panel identifies which zones are bypassed on a Partial
Closing. To do this, the panel will send the partial closing
reporting code, and then the alarm restore reporting code(s)
for the zone(s) which are bypassed.
For example, if a panel is armed with Access Code 40 with
Zones 3 and 5 bypassed, the panel will transmit:

Partial Closing
Alarm Restore Zone 3
Alarm Restore Zone 5
Closing By User Code 40

The panel will follow the

Alarm Restore Call Direction

options programming.

NOTE:This feature does not apply to the SIA format, which
uses CG-ZZ to identify zones for Partial Close.

NOTE:The LINKS2X50 does not communicate Alarm Restore
events.

Closing Confirmation . . . . . . . . . . . . . . . . . .Section [381]: [4]