background image

12

Dräger Polytron 8000

Operation

4

Operation

4.1

Operating fundamentals

4.1.1

Menu navigation

It is possible to scroll through he menu items by tapping the 

and   symbols with the magnetic wand (Part Number 4544101,

blue).   confirms a function.

Graphic symbols facilitate navigation in the various menus.

4.1.2

Changing parameter values or the parameter status

1. Select the desired menu item with   and  .
2. Confirm the menu item with  .

The current value or status will be displayed.

3. Using   and  , the value of a numerical parameter can

be changed or preset values can be selected.

4. As soon as the desired value or the selection is displayed,

tap   to validate/confirm the new parameter.

5. Tap   to access the next higher level.

z

If exiting using 

Back to menu

 or 

Previous

, all changes will

be discarded.

4.1.3

Exiting menus

z

 Tap 

Back to measurement

 and   to exit the menu.

4.2

Display and LEDs

In measurement mode, the current gas concentration, the name

of the gas and the measurement units are shown on the display.

The green LED is lit.

In addition, the following symbols may be displayed:

z

↑ ↑ ↑ ↑

 

", if the measurement range is exceeded.

z

- - - -

 " and " 

X

 " in the event of a malfunction. The yellow

LED is lit, (see chapter 4.2.2 on page 13).

z

"SIL", when SIL status is activated.

When the optional relay PCB is used:

z

If the first alarm has been triggered, the red LED flashes

single and A1 is displayed.

z

If the second alarm has been triggered, the red LED

flashes double and A2 is displayed.

NOTICE

The housing cover should be fitted when using the 

magnetic wand. If the housing cover is not fitted, 

the magnetic wand might activate two or more buttons 

at the same time (crosstalk).

With the text " back ", " Menu " etc.

close menu or 1 step back.
Closed folder

Further functions or sub-menus are located under 

this item.
Opened folder

The functions and sub-menus available here are listed 

under this item.
Function

When activated, functions can be executed in one or 

more steps.
Selection activated

For functions that can be selected and activated, the 

activation is initiated by touching "

".

List closed above / complete

There are no further functions, menus or sub-menus 

listed above.
List can be scrolled upwards

There are further functions, menus or sub-menus 

listed above.

00733300.eps

M

OK

i

i

OK

List closed below / complete

There are no further functions, menus or sub-menus 

listed below.
List can be scrolled downwards

There are further functions, menus or sub-menus 

listed below.
Next

Perform context-related action.
Number / total number of steps (screens) within 

the function.
Entry

Enter data with "

" and "

".

3/3

2/2

M

M

OK

M

OK

OK

OK

Summary of Contents for Polytron 8000






































Reviews: