manualshive.com logo in svg

Dräger Evita V300, Supplement To Instructions For Use

Share
Download
Dräger Evita V300 Supplement To Instructions For Use Download Page 35

35

Technical data

Essential performance characteristics

Applies to:
– Evita Infinity V500
– Babylog VN500
– Evita V300

The essential performance consists in a controlled 
and monitored patient ventilation with user-defined 
settings for the monitoring functions
– minimum and maximum tidal volume,
– maximum airway pressure,
– minimum and maximum O

2

 concentration in the 

breathing gas,

or, if a set limit is exceeded, an appropriate alarm.

Additionally, the integrated monitoring alarms in the 
following situations:
– Failure of the external power supply
– Battery discharge
– Failure of the gas supply

Maximum load

Universal holder with standard rail (G93140)

10 kg (22 lbs)

Humidifier holder, can be swiveled (G93111)

5 kg (11 lbs)

Humidifier holder, side rail (8416325)

5 kg (11 lbs) 
If a hinged arm is attached to the side rails of the 
ventilation unit in addition to the humidifier holder 
(8416325), the maximum load of 5 kg (11 lbs) per 
side rail must be observed. The humidifier holder 
can then only support 4 kg (8.8 lbs).

Operating data (cont.)

Summary of Contents for Evita V300











































Reviews:

No comments

Brands by name

Popular brands

Load more brands