manualshive.com logo in svg

Dräger Evita V300, Supplement To Instructions For Use

Share
Download
Dräger Evita V300 Supplement To Instructions For Use Download Page 10

Assembly and preparation

10

Connecting the mains power supply

Connecting the nurse call

Transportation of patients within the hospital

When transporting the patient within the hospital, 
grasp the trolley handle firmly and push the device 
in longitudinal direction.

WARNING
Risk of electric shock and of device failure

If the device is connected to a power socket 
with incorrect mains voltage or without a pro-
tective ground, the user can be injured and the 
device damaged.

Only connect the power cable to power sock-
ets with a protective ground and the correct 
mains voltage. Observe the technical data.

NOTE

The mains power socket in use must be freely ac-
cessible during operation.

WARNING
Risk of patient injury

All data transferred via the nurse call are for 
information only and must not be used as the 
sole basis for diagnostic or therapeutic deci-
sions. The nurse call is not intended for use 
with a distributed alarm system according to 
IEC 60601-1-8:2012.

Summary of Contents for Evita V300











































Reviews:

No comments

Brands by name

Popular brands

Load more brands