manualshive.com logo in svg

Dräger Evita V300, Supplement To Instructions For Use

Share
Download
Dräger Evita V300 Supplement To Instructions For Use Download Page 21

21

Configuration

Setting the priority of the battery alarm

The device offers the following priorities for battery 
alarms:

The 

Battery activated

 alarm message indicating 

the changeover to battery operation can be config-
ured as a high- or medium-priority alarm when 

Dräger ventilation

 is selected.

z

Touch the 

Medium

 (D) or 

High

 (E) button and 

confirm.

Depending on the setting (IEC/CEI or Dräger venti-
lation), alarm messages have the following priority:

B

IEC/CEI

Priority of the battery alarm in ac-
cordance with IEC 60601-2-12

C

Dräger 
ventilation

Priority of the battery alarm ac-
cording to Dräger

Alarm message

Priority

 IEC/CEI

Priority 

Dräger ventilation

Battery activated

Low-priority alarm message

High-priority or medium-priority alarm 
message

Battery low

Medium-priority alarm message

High-priority alarm message

Battery discharged

High-priority alarm message

High-priority alarm message

Summary of Contents for Evita V300











































Reviews:

No comments

Brands by name

Popular brands

Load more brands