manualshive.com logo in svg

Dräger Evita V300, Supplement To Instructions For Use

Share
Download
Dräger Evita V300 Supplement To Instructions For Use Download Page 25

25

Alarm – Cause – Remedy

!!!

253

Device failure (11)

A failure was detected 
during the start-up phase.

Disconnect patient from the 
device and continue 
ventilation without delay 
using another independent 
ventilator.

Call DrägerService.

!!!

253

Device failure (12)

A system failure was 
detected.

Disconnect patient from the 
device and continue 
ventilation without delay 
using another independent 
ventilator.

Call DrägerService.

!!

090

Device failure (13)

The broken wire detection 
for the flow sensor is faulty.

Ventilation functions are not 
affected.

Call DrägerService.

!!!

237

Device failure (2)

Internal safety system 
failure.

Do not use this device for 
ventilation therapy.

Call DrägerService.

!!

140

PEEP high

Expiratory valve or 
breathing circuit 
obstructed.

Check breathing circuit and 
expiratory valve.

Check for condensate.

Expiratory resistance 
increased.

Check viral/bacterial filter. 
Replace it if necessary.

Device failure.

Disconnect patient from the 
device and continue 
ventilation without delay 
using another independent 
ventilator.

Call DrägerService.

!!!

140

PEEP low
Applies only to 
Babylog VN500.

Measured PEEP is 3 mbar 
(3 cmH

2

O) less than set 

PEEP.

Check breathing circuit for 
tight connections.
Check whether the 
expiratory valve is properly 
engaged.
Make sure that the tube or 
mask is connected 
correctly.

Alarm 
priority

Alarm message

Cause

Remedy

Summary of Contents for Evita V300











































Reviews:

No comments

Brands by name

Popular brands

Load more brands