manualshive.com logo in svg

Dräger Evita V300, Supplement To Instructions For Use

Share
Download
Dräger Evita V300 Supplement To Instructions For Use Download Page 20

Configuration

20

Configuration

Applies to:
– Evita Infinity V500
– Babylog VN500
– Evita  V300

Information on configuration

The Exchange intervals page has been renamed to 

System status

. Information on the exchange inter-

vals can be found at 

System setup > System sta-

tus > Exchange intervals

. Additional information 

regarding the 

System status

 page can be found on 

page 22.

The 

System status

 page is password-protected.

Configuring alarm settings

Setting the alarm tone

Setting the minimum alarm volume

Configuring the minimum alarm volume sets the 
lower limit of the factory setting for the volume of 
the alarm tone (10 % to 100 %). This allows the 
setting range to be adjusted to the acoustical situa-
tion at operation site.

Prerequisite: The 

System setup > Alarms > 

Alarm vol./tone

 page is opened.

1

Touch the (A) button.

2

Set the value for the minimum volume by turn-
ing the rotary knob and push to confirm.

WARNING
Missing alarms in loud environments

Alarm situations are not detected.

Set the volume of the alarm tone so that 
alarms can be heard.

149_neu

System setup

A

B C

D E

Summary of Contents for Evita V300











































Reviews:

No comments

Brands by name

Popular brands

Load more brands