Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 82

Page: 82 / 136

Issued May 2020
Maintenance and Adjustment

Printed in the U.S.A.

Maintenance and Adjustment

BODY DAILY CHECKLIST

Make sure you perform a daily check of the unit. Refer to the Operator’s Manual for the Daily Checklist. Many checks in the
Daily Checklist are maintenance related, such as checking tire pressures and hoses for wear and damage.

DAILY CHECKLIST MAINTENANCE ITEMS

Item

Required Action

Low air pressure in tires

Inflate the tire to the correct air pressure given on the tire.

Worn tire

Replace when the wear is greater than allowed by law or
before the tread is no longer visible.

Damaged tire

Replace immediately BEFORE going on route.

Hydraulic pump leaks

Determine the cause of the leak and repair immediately.

Damaged hydraulic pump

Repair or replace IMMEDIATELY.

Loose or missing hardware for the hydraulic pump

Tighten loose hardware.
Replace missing hardware immediately.

Damaged decal or decal not readable

Replace decal immediately.

Low level of hydraulic oil

Fill the hydraulic oil tank immediately.

Worn or damaged hoses

Replace immediately.

Leaks at cylinders, hoses or fittings

Tighten loose connection.

Loose or missing hardware

Tighten loose connections.
Replace missing hardware.

Worn fiber guards

Replace hoses/fittings as necessary.
Install new fiber guard on new hoses.

Worn or damaged tailgate lock components

Replace worn or damaged components.

Loose or missing tailgate lock hardware

Tighten loose hardware.
Replace missing hardware.

Damaged tailgate seal

Replace seal.

Body structure has loose or missing hardware

Tighten loose hardware.
Replace missing hardware.

Body structure has cracked weld joints

Repair immediately.

Body mounting brackets have loose hardware,
damaged hardware or cracked welds

Tighten loose hardware.
Replace missing hardware.
Repair cracked welds.

Air regulator

90 PSI, typically located at front of body.

Operation

Operate All Functions to make sure all functions work
correctly.

Summary of Contents for HEIL LIBERTY TP1L-SM-0520










































































































Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands

Dover HEIL LIBERTY TP1L-SM-0520, Service Manual

Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands