Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 55

Page: 55 / 136

Issued May 2020

Lift Arm

Lift Arm

CHECK LIFT AND TORQUE MOUNT BASE BOLTS (CONTINUED)

Figure 13. Lift Mount Bolt

7. Use a wrench and extension handle to turn the nut's marked corner to the second mark at the center of the fourth nut

flat. It is critical that the head of the bolt is held in place and not allowed to rotate further. Brace the wrench handle as
necessary.

8. Weld the nut to the bolt as specified. Welding the nut prevents the nut from loosening and prevents the bolt and nut

from being reused.

9. Do not remove paint marks

Figure 14. Lift Mount Bolt Location

Figure 15. Lift Mount Bolt

Location

Summary of Contents for HEIL LIBERTY TP1L-SM-0520










































































































Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands

Dover HEIL LIBERTY TP1L-SM-0520, Service Manual

Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands