Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 67

Page: 67 / 136

Issued May 2020

Lift Arm

Lift Arm

LIFT AND WELD CRACKS DECISION TREE

Use this decision tree to help you decide whether to repair a crack or to replace the entire lift arm.

Follow these welding requirements for repairing the lift arm.

1. All material shall be free from paint, soil, grease, dirt, and any other non-metal contamination.

2. Weld according to the Weld Procedure.

3. All welds shall be in conformance of AWS D1.1.

4. Inspection supervisor required.

5. Attach the ground lead as close as practical to the section where you are working. Disconnect the battery negative or

ground cable from the battery.

Summary of Contents for HEIL LIBERTY TP1L-SM-0520










































































































Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands

Dover HEIL LIBERTY TP1L-SM-0520, Service Manual

Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands