Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 33 | Manualshive

Page: 33 / 136

background image

Issued May 2020

General Information

Copyright 2020, Heil Environmental
Printed in the U.S.A.

General Information

27

COLD WEATHER WARMUP PROCEDURE

When ambient air temperature is cold (below 0 degrees F), it is necessary to warm up the unit’s hydraulic oil before you
start your daily route operation, check the oil level, or adjust hydraulic pressure settings. The hydraulic oil is sufficiently
warmed when the temperature is between 120° and 160°F.

WARNING

Moving parts on the unit are dangerous. Serious injury or death can occur if a person is struck by the equipment. Clear all
people from the area before you operate the unit.

Follow the steps below to warm up the hydraulic oil.

1. START the TRUCK and let the engine idle.

2. APPLY the PARKING BRAKE and make sure it holds.

3. ENGAGE the HYDRAULIC PUMP for approximately five minutes.

4. MAKE SURE the AREA IS CLEAR of all unnecessary people BEFORE you operate the controls.

5. OPERATE the PACKER EXTEND and PACKER RETRACT functions through ten (10) cycles while the engine idles.

See the Operator’s Manual for operation instructions.

6. Make sure the oil temperature on the site gauge is between 120° and 160°F. If not, repeat step 5.

7. Check for fluid leaks. Repair if necessary.

8. The unit is now ready to go on route.

BATTERY DISCONNECT SWITCH

The battery box is typically located on the streetside of the chassis frame near the front of the body, however it can be
mounted at a different location on different chassis. Become familiar with the location of the battery box and battery
disconnect switch on your unit.

1. You must turn the battery disconnect switch to the OFF position whenever the unit is shut off for any length of time –

especially when the unit will be left unattended.

2. You must turn the battery disconnect switch to the ON position whenever you will use the unit.

3. You must check the position of the battery disconnect switch as part of the daily inspection.

NOTICE

Battery cables must be securely anchored and not rubbing other equipment. Cable insulation must be free of damage and
abrasion. Inspect weekly.

NOTICE

Always disconnect the battery before welding on the chassis or body.

«
...
31
32
33
34
35
...
»

Summary of Contents for HEIL LIBERTY TP1L-SM-0520









































































































































Reviews:

No comments

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brand: Keithley Pages: 149

Brand: Raven Pages: 27

Brand: Raven Pages: 79

Brand: Raven Pages: 88

SATURA SPOT LED PRO

Brand: Elation Pages: 41

Brand: Tapco Pages: 16

Brand: Zenbooth Pages: 40

Visium CytAssist

Brand: 10x Genomics Pages: 51

Chromium X Series

Brand: 10x Genomics Pages: 5

Brand: Danelec Pages: 67

Brand: G-Lab Pages: 16

Brand: G&G Pages: 2

Aspect Q-CARD 100-4T

Brand: idi Pages: 38

ThermoTweez Handpiece TT-65

Brand: Pace Pages: 14

Brand: Nady Audio Pages: 2

Brand: Jandy Pages: 52

WaterLink Spin Touch DW

Brand: LaMotte Pages: 64

High End Systems SolaPix 7

Brand: ETC Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands