Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 57 | Manualshive

Page: 57 / 136

background image

Issued May 2020

Lift Arm

Copyright 2020, Heil Environmental
Printed in the U.S.A.

Lift Arm

51

UNIVERSAL BELT AND TRI-CUFF GRABBER ADJUSTMENTS (CONTINUED)

B. 90-300 Gallon Belt Grabbers

Adjust the grabber belt length so the distance between the inner arm and the outside roller is approximate 30” (+/- 1”) to
obtain a firm grip for smaller containers. The total overall length of the grabber belt must be set to obtain a firm grip for
larger containers. See illustration below.

NOTICE

Do not adjust the total overall belt length too far as this may cause the grabber belt to touch or wear against the outer arm.

NOTICE

When used with the Python lift the grabbers should be adjusted so the outer rollers do not touch each other when the
grabbers are completely closed.

Figure 17. 90-300 Gallon Belt Grabbers

«
...
55
56
57
58
59
...
»

Summary of Contents for HEIL LIBERTY TP1L-SM-0520









































































































































Reviews:

No comments

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brand: CAIRE Pages: 2

Brand: A.MENARINI Pages: 2

Brand: Mandam Pages: 9

Brand: Warehouse-lighting Pages: 3

Brand: Eagle Group Pages: 8

Brand: E2S Pages: 5

Brand: Eaton Pages: 21

Brand: Eaton Pages: 70

Brand: NANO Pages: 4

Brand: Hacker Pages: 2

Brand: J.P. SELECTA Pages: 8

Brand: Haemonetics Pages: 134

Brand: Hadeco Pages: 72

Brand: Taylor-Wharton Pages: 25

Brand: i-CAT Pages: 96

Brand: Raven Pages: 48

Brand: Pacific Pages: 16

Brand: TATU Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands