manualshive.com logo in svg

Dormakaba Axessor CIT, Technical Manual

Share
Download
Dormakaba Axessor CIT Technical Manual Download Page 42

Functionality

Technical Manual

42

V28 - 08/2019

Electronic safe lock

User Code

Description

Result

User Codes 45 and
46

It is possible to define User
Codes 45 and 46 as Impulse
Code via AS284-USBW or
AS284-NETW.

It is possible to define the Im-
pulse Code for each output of
the lock or eBox via AS284-
USBW or AS284-NETW (max.
2 outputs).

When entering either User Code 45
or 46 an impuls is generated on the
respective output.

If this function is activated, it is not
possible to open the lock with the
User Codes 45 and 46.

User Code 47

It is possible to define the User
Code 47 as Time, Audit and
Battery Code via AS284-
USBW or AS284-NETW.

The User Code 47 has access to all
functions relating time, date,
weekly and holiday programs.

It is not possible to open the lock
with User Code 47.

If the User Code 47 is configured as
Audit or Battery Code via AS284-
USBW or AS284-NETW, the user
can either read the audit or reset
the battery message after the bat-
tery compartment had been
opened.

User Code 48

It is possible to define the User
Codes 48 and 49 via AS284-
USBW or AS284-NETW to de-
activate or activate the lock
opening.

When entering the User Code 48,
the lock does not open, lock dis-
abling is activated.
The lock rejects any opening code.

When entering the User Code 49,
lock enabling is activated.

User Code 49

11.7.2.4

Courier Code

There is only 1 Courier Code (Courier Code ID 90) which is provided for special staff from
Cash-In Transit services (CIT) responsible for filling or emptying secured containers without
any configured Time Delays.

Factory setting:

No code assigned

Functions:

Opening the lock, even in Dual Mode by bypassing a
Time Delay
Alteration of Courier Code

Courier Code func-
tion

Description

Result

"Courier does not
open but skips Time
Delay"

When entering the Courier
Code to open the lock, the
Time Delay will be skipped for
the next opening.

The Confirmation Window count-
down indicates the duration of this
condition. 
The opening procedure must start
during countdown.

11.7.2.5

Duress Code

If the lock is connected to an external alarm system, it is possible for the operator to activate
a silent duress alarm which is imperceptible for the aggressor.

It depends on the current operating mode in which way a duress alarm is activated.

The Courier Code always opens the lock with a time delay.
This behavior is irrespective of configured time delays and also applies in case of a possible
threat.

Summary of Contents for Axessor CIT






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands