manualshive.com logo in svg

Dormakaba Axessor CIT, Technical Manual

Share
Download
Dormakaba Axessor CIT Technical Manual Download Page 103

Configuration

Technical Manual

103

V28 - 08/2019

Electronic safe lock

1.

Select the submenu DUAL bank.

2.

Press the ENTER key.

ð

The currently set status of the Dual Mode will be displayed.
By default Dual Mode is set to off.

3.

Use the LEFT or RIGHT arrow key to activate (DUAL ON) or deactivate (DUAL OFF) the
Dual Mode.

4.

Press the ENTER key to confirm the setting.

15.1.9.14

Activating or deactivating One Shot Codes

When opening the lock with the Master Code, the code remains unchanged (no automatic
deletion).

When opening the lock with the Manager Code 40, the code remains unchanged (no auto-
matic deletion).

When opening the lock with a One Shot Code of user group 4, the code remains unchanged, if
the Time Delay of user group 1 is set to the value "0" and the One Shot Code is confirmed by
either the Master Code, 1 code of user group 1 or the Courier Code.

This function defines whether codes of user group 4 will be used as One Shot Codes.
If this function is activated, the defined codes of user group 4 are only valid for 1 single open-
ing.

Authorization: Master Code

1.

Select the submenu ONE SC4 bank.

2.

Press the ENTER key.

ð

The message is displayed If One Shot Codes are activated (ON) or deactivated (OFF).

3.

Select either ON or OFF by using the LEFT or RIGHT arrow key.

4.

Press the ENTER key to confirm the setting.

5.

Select "YES" in the "SAVE?" dialog by using the LEFT or RIGHT arrow key.

6.

Press the ENTER key to confirm the setting.

15.1.9.15

Activating or deactivating the Time Lock in OTM

Ex factory there is no defined Time Lock Period for OTM codes
OTM codes must be set to ON if defined Time Lock Periods will be applied.

Authorization: Master Code

1.

Select the submenu TL LOCK cit.

Summary of Contents for Axessor CIT






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands