Doosan DV11 Page 168 Operation And Maintenance Manual Download

Page: 168 / 220

DV11

Operation and Maintenance

163

Engine Diagnostic

Printed in Mar. 2005 PS-MMA0608-E1A

3.8.11. Vehicle operating record

The vehicle information related to the operating is recorded in the electric control

unit (ECU).

- The measurement of the operating record is possible after the accumulated

value or the switch

『

reset

』

is depressed.

The contents recorded in the electric control unit

- Fuel quantity according to the division : total, idle state, PTO
- Fuel consumption rate.
- operating mileage.
- Engine operating time, ECU using time.

The monitoring is possible by using diagnostic tool.

3.8.12. Power take off (PTO)

Power take off (PTO) of the operation mode is controlled.

Operation condition

- Cruise control switch

: no trouble

- Brake pedal

: no trouble, not depressed

- Engine brake switch

: off

- Parking brake

: operated

- Clutch pedal

: not depressed

- Vehicle speed

: stop

Operation method

- Operation of PTO is possible by using the cruise control switch.

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for DV11





























































































































































































































Search results

Summary of Contents for DV11

Reviews:

Related manuals for DV11

Brands by name

Popular brands

Doosan DV11, Operation And Maintenance Manual

Search results

Summary of Contents for DV11

Reviews:

Related manuals for DV11

Brands by name

Popular brands