Doosan DV11 Operation And Maintenance Manual Download Page 109

Page: 109 / 220

DV11

Operation and Maintenance

104

Engine Reassembly

Printed in Mar. 2005 PS-MMA0608-E1A

3.3.20. Fuel high pressure pump

Assemble the gear of the fuel high

pressure pump by using specified

tool.

Gear nut torque

11±0.5 kg.m

Install the fuel high pressure pump

on the backside of the fly wheel

housing.

Assemble the stud bolt after apply

the loctite.

Assemble the fuel high pressure

pump fixing bolts with specified

torque.

Torque 4.4

kg.m

3.3.21. Intake manifold

Attach a new gasket to the cylinder

head side.

Assemble the intake manifold by

tightening the fixing bolts.

Assemble both sides by the above

method.

Attach a gasket to the equalizing

pipe that connects the intake

manifolds of both sides and

assemble both manifolds by

tightening the fixing bolts.

Torque 2.2

kg.m

Fuel high
pressure pump

Driving gear

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for DV11





























































































































































































































Search results

Summary of Contents for DV11

Reviews:

Doosan DV11, Operation And Maintenance Manual, Page: 109 / 220

Search results

Summary of Contents for DV11

Reviews: