Doosan DV11 Operation And Maintenance Manual Download Page 114

Page: 114 / 220

DV11

Operation and Maintenance

109

Engine Reassembly

Printed in Mar. 2005 PS-MMA0608-E1A

Connecting rod bolt

3.5 kg.m

Liner fixing bolt

4 kg.m

Torque

Head bolt

3 kg.m

3.3.31. Power steering pump

Assemble the power steering pump

to the fly wheel housing.

Set the power steering pump to the

driving coupling carefully to prevent

from damage of the O-ring.

Assemble the steering pump fixing

bolt by specified torque.

Torque 4.4

kg.m

3.3.32. Power take off (P.T.O)

Assemble the P.T.O assembly to

the fly wheel housing carefully to

prevent from damage of the O-ring.

Assemble the P.T.O gear fixing nut

and coupling nut by specified

torque.

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for DV11





























































































































































































































Search results

Summary of Contents for DV11

Reviews:

Doosan DV11, Operation And Maintenance Manual, Page: 114 / 220

Search results

Summary of Contents for DV11

Reviews: