manualshive.com logo in svg

Doosan DV11, Operation And Maintenance Manual, Page: 181 / 220

Share
Download
Doosan DV11 Operation And Maintenance Manual Download Page 181

 

DV11 

  Operation and Maintenance

 

 

176

Commissioning and Operation

Printed in Mar. 2005    PS-MMA0608-E1A

Rocker arm 

Caliper adjusting bolt 

Caliper

Intake valve 

spring 

Intake valve 

Valve seat 

Valve adjusting bolt

Valve adjusting nut

Push rod 

Valve adjusting 
bolt 

Rocker arm 

Push rod 

Caliper adjusting nut

Caliper

Exhaust valve spring

Exhaust valve

Valve seat

A 

C

B

Intake valve adjusting

Exhaust valve, engine brake adjusting

Engine brake

Engine brake Adjusting bolt

 

4.8. Adjustment of valve clearance 

4.8.1. General information 

The valve clearances are to be adjusted at the times of the following situations. 

z

 When the engine is overhauled and the cylinder heads are disassembled. 

z

 When severe noise comes from valve train. 

z

 When the engine is not normally operated, even though there is no trouble in the 

fuel system. 

 
 

4.8.2. Valve clearance adjust procedure 

z

  After letting the #1 cylinder's piston come at the compression top dead center by 

turning the crankshaft, adjust the valve clearances. 

z

  Loosen the lock nuts of rocker arm adjusting screws and push the feeler gauge 

of specified value between a rocker arm and a valve stem and adjust the 
clearance with adjusting screw respectively and then tighten with the lock nut. 

z

  As for the valve clearance, adjust it when in cold, as follows. 

 

Engine model  Intake valve (A) Exhaust valve (B)  Engine brake (C)

DV11

 

0.4 mm 

0.5 mm 

1.5 mm 

 

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for DV11





























































































































































































































Reviews:

No comments