manualshive.com logo in svg

Doosan DV11, Operation And Maintenance Manual, Page: 64 / 220

Share
Download
Doosan DV11 Operation And Maintenance Manual Download Page 64

 

DV11 

  Operation and Maintenance

 

 

61

Engine Disassembly

Printed in Mar. 2005    PS-MMA0608-E1A

 

z

  Allow an interval of 2 ~ 3 minutes 

until the engine oil by-passes to the 

oil pan, then take off the filter. 

 

 

 

 

 

z

 Unscrew the oil filter head fixing 

bolts and take off the oil filter head 

 

 

 

 

 

 

3.1.20. Water pump 

z

 Loosen the various hose clamps 

for the connections. 

z

 

Remove the cooling water 

discharging pipe and disassemble 

the thermostat. 

z

 Remove the cooling water pump 

fixing bolts and disassemble the 

cooling water pump. 

 

3.1.21. Starting motor 

z

 Remove the starting motor fixing 

nuts and disassemble the starting 

motor. 

 

 

 

 

 

 

Water pump 

Thermostat 

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for DV11





























































































































































































































Reviews:

No comments