background image

1506-065-K-6-17

1

TABLE OF CONTENTS

SPECIFICATIONS

 1504 

Specifications

 1506 

Specifications

 Important 

Notices

SECTION 1 - INSTALLATION

 

 

1.1 Remove Faceplate from Cabinet

 

1.2 Surface Mount

 

1.3 Flush Mount

 

1.4 Terminal Wiring

 

1.5 1504 AiPhone Intercom Station Connections

 

1.6 Secondary Keypad Wiring

SECTION 2 - PROGRAMMING

 

2.1 Re-Programming the Master Code

 

2.2 Relay Strike Time

 

2.3 X Strikes for Invalid Entry Code Attempts

 

2.4 Programming Four-digit Entry Codes

 

2.5 Erase a Four-digit Entry Code

 

2.6 Erase ALL Four-digit Entry Codes

 

2.7 Four-digit Entry Code Divide Number

 

2.8 Programming Five-digit Entry Codes

 

2.9 Erase a Five-digit Entry Code

 

2.10 Erase ALL Five-digit Entry Codes

 

2.11 Five-digit Entry Code Divide Number

 

2.12 Hold Boundary Programming

 

2.13 Time ZONE 1 Boundary Programming

 

2.14 Time ZONE 2 Boundary Programming

SECTION 3 - OPERATING INSTRUCTIONS

 

 

3.1 Four-digit Entry Codes

 

3.2 Five-digit Entry Codes

 

3.3 Request to Exit Input (Terminals 1 and 12)

 

3.4 Door Open Input (Terminals 2 and 12)

 

3.5 Hold Feature Operation

 

3.6 Time Zone Operation

SECTION 4 - MAINTENANCE

 

 4.1 

Troubleshooting

 

4.2 Log Tables

2

2

3

4

 

4

 

4

5

5

6

7

8

9

9

9

9

10

10

10

10

11

11

11

11 

12

12

12

13

13

13

13

13

14

15

16

16

17-19

Summary of Contents for 1506-086























Reviews: