manualshive.com logo in svg

DOMUSA TEKNIK BioClass iC 66, Installation And Operating Instructions Manual

Share
Download
DOMUSA TEKNIK BioClass iC 66 Installation And Operating Instructions Manual Download Page 78

EN 

78

 

 

BIOCLASS iC 66 

Code 

Alarm 

Description 

E-42 

Communication error with 

BIO 

Hydraulic Kit

 (not valid for BIOCLASS 

iC 66). 

Communication failure between boiler and the 

BIO Hydraulic 

Kit

. 

If this alarm occurs repeatedly contact the nearest official 

technical assistance service. 

E-43 

Ashtray full. 

Warning that the ashtray is full. The boiler will continue 

operate normally. To restore warning, the ashtray must be 
emptied and it is necessary to set the “Emptying ashes” 

parameter to 0 of the “User menu” (See “Ashtray status”).  

E-44 

Boiler Maintenance.  

Notice for maintenance of the boiler. Contact your nearest 

official technical assistance service to perform periodic 

maintenance of the boiler. 

E-45 

BT tank temperature sensor open 

circuit, 

Sbt

. 

BT tank temperature sensor is damaged or disconnected. 

Contact your nearest official technical assistance service to 

have it replaced. 

E-46 

BT tank temperature sensor short-

circuited, 

Sbt

. 

E-47 

Communication error with pellets level 

sensing unit. 

Communication failure between boiler and the pellets sensing 

system board (PCB). 
If this alarm occurs repeatedly contact the nearest official 

technical assistance service. 

E-48 

Low fuel level in the hopper. 

Warning that the hopper is going to run out of pellets (fuel 

reserve). The boiler will continue operate normally. Refill the 

hopper with pellets up to the sensor to restore the warning 

alarm. 

E-49 

Hopper is run out of fuel. 

The hopper is completely empty of pellets. The boiler stops 

running to avoid emptying the auger. To restore boiler 

functioning refill the hopper with pellets up to the sensor and 

press RESET button. 

E-50 

Fuel Suction System and pellets sensing 

units connected together. 

Fuel Suction System and pellets sensing units are connected 

together to boiler's main board. Contact your nearest official 
technical assistance service to disconnect one of the units. 

E-57 

Zone 1 

TA

1

 room temperature sensor 

open circuit. 

The Zone 1 room temperature device is broken or 

disconnected. Please contact your nearest official Technical 
Assistance Service to have it replaced. 

E-58 

Zone 1 

TA

1

 room temperature sensor 

short-circuited. 

E-59 

Zone 2 

TaM

1

 room temperature sensor

open circuit. 

The Zone 2 room temperature device is broken or 

disconnected. Please contact your nearest official Technical 

Assistance Service to have it replaced.

 

E-60 

Zone 2 

TaM

1

 room temperature sensor

short-circuited. 

E-61 

Zone 3 

TaM

2

 room temperature sensor

open circuit. 

The Zone 3 room temperature device is broken or 

disconnected. Please contact your nearest official Technical 

Assistance Service to have it replaced.

 

E-62 

Zone 3 

TaM

2 

room temperature sensor 

short-circuited. 

Summary of Contents for BioClass iC 66

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands