DOMUSA TEKNIK BIOCLASS iC 150 Installation And Operating Instructions Manual Download Page 76

Page: 76 / 80

BIOCLASS iC 150

code ALARM

DESCRIPTION

E-62

Low oxygen concentration.

The lambda sensor has measured an oxygen

concentration that is too low over a long period. The
boiler will perform safety interlock.
Please contact your nearest official Technical

Assistance Service to have it replaced.

E-63

High oxygen concentration

The lambda sensor has measured an oxygen

concentration that is too high over a long period. The

boiler will perform safety interlock.
Please contact your nearest official Technical

Assistance Service to have it replaced.

E-64

Lambda sensor error

The lambda sensor has given a value outside of the

range in the calibration process. While adjusting the

combustion with the lambda sensor enabled the boiler
will perform safety interlock.
Please contact your nearest official Technical

Assistance Service to have it replaced.

E-65

Lambda sensor open circuit

The lambda sensor is broken or badly connected.

Please contact your nearest official Technical

Assistance Service to have it replaced.

E-66

Lambda sensor shortcircuited

E-68

External alarm

Error generated by an external alarm. The boiler will

lock-out until the external alarm has been reset.

E-80

Upper sensor

Scol

of the

MC Cascade

control

open circuit

The Scol probe is damaged or disconnected. Please

contact your nearest official Technical Assistance
Service to have it replaced.

E-81

Upper sensor

Scol

of the

MC Cascade

control

shortcircuited

E-82

Upper sensor

Sdown

of the

MC Cascade

control

open circuit

The Scol probe is damaged or disconnected. Please

contact your nearest official Technical Assistance

Service to have it replaced.

E-83

Upper sensor

Sdown

of the

MC Cascade

control

shortcircuited

E-84

Too many

Sbt

sensors connected

simultaneously in the cascade system

Intermediate temperature probes in the buffer tank

have been connected. The MC cascade control

supports a maximum of 2 intermediate probes.

Disconnect the remaining probes.
If this alarm occurs repeatedly, please contact the
nearest official Technical Assistance Service.

E-86

Maximum power insufficient

The control has reduced the maximum power of the

boiler below a suitable level due to measuring an
insufficient air quantity in the burner input.

If this alarm occurs repeatedly, please contact the

nearest official Technical Assistance Service.

E-87

Sensor

Sbt2

connected to the cascade

system

Sbt2

has been connected to the boiler and will not

operate for the cascade system.

Summary of Contents for BIOCLASS iC 150

















































































Search results

Summary of Contents for BIOCLASS iC 150

Reviews:

Related manuals for BIOCLASS iC 150

Brands by name

Popular brands

DOMUSA TEKNIK BIOCLASS iC 150, Installation And Operating Instructions Manual

Search results

Summary of Contents for BIOCLASS iC 150

Reviews:

Related manuals for BIOCLASS iC 150

Brands by name

Popular brands