manualshive.com logo in svg

DOMAILLE ENGINEERING APM-HDC-5400 Series, User Manual

Share
Download
DOMAILLE ENGINEERING APM-HDC-5400 Series User Manual Download Page 25

23

2. Use the keypad to set hours of use before Replacing the Rubber

    Pad. The recommended interval is 320 hours. This can be

    modified as needed based on actual working conditions.

Annual Maintenance

The Annual Maintenance is tied to the number of hours the platen is 

rotating. To set the Annual Maintenance interval:

1. Use a stylus to press the number located under “Hour Interval”

    tab. This will access the keypad for data entry.
2. Use the keypad to set hours of use before Replacing the Annual    

    Maintenance. The recommended interval is 2080 hours. This can 

    be modified as needed based on actual working conditions.

Replace Air Cleanse Filter

The Replace Air Cleanse Filter maintenance schedule is tied to the 

number of hours the Platen is rotating. To set the Replace Air

Cleanse Filter maintenance interval:

1. Navigate to Page 2 of maintenance items.
2. Use a stylus to press the number located under “Hour Interval”

    tab. This will access the keypad for data entry.
3. Use the keypad to set hours of use before Replacing the Air

    Cleanse Filter. The recommended interval is 320 hours. This can

    be modified as needed based on actual working conditions.

EZ Check Wear Test Kit

1. Use a stylus to press the number located under “Hour Interval”

    tab. This will access the keypad for data entry.

Fig. 6B

Summary of Contents for APM-HDC-5400 Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands