manualshive.com logo in svg

DLC SA-230FA, Instruction Manual, Page: 4 / 38

Share
Download
DLC SA-230FA Instruction Manual Download Page 4

3 

user is required. 

Warning:

  If the ALARM indicator light 

  illuminates, the machine is over-pressure or 

overheated. The sterilizer will shut down automatically. Contact your supplier for 

service support. 

Warning:

  Failure to follow the Maintenance Instructions will adversely affect performance 

and lifespan of the sterilizer, and may invalidate the warranty. 

Warning:

  Always keep the sterilizer clean. 

Warning:

  In an emergency, or before carrying out any maintenance, always disconnect the 

power cord from the outlet. 

Warning:

  A separate (dedicated) circuit is recommended for the sterilizer. The sterilizer 

should not be connected to an electrical circuit with other appliances or 

equipment. 

Warning:

  Please unplug the power cord and drain off water from the reservoir if the 

sterilizer will not be used regularly. 

Warning:

  Always check the status of the electric wire; unplug the power cord if breakage 

comes up. Contact your supplier for service support. 

Summary of Contents for SA-230FA







































Reviews:

No comments