manualshive.com logo in svg

dji Naza, User Manual, Page: 27 / 43

Share
Download
dji Naza User Manual Download Page 27

©2012 DJI Innovations. All Rights Reserved.       

                                                                                                                                27 

   

5 Gimbal 

 

 

STEP1:  Gimbal Switch 

If you use gimbal, please choose On here, and select an Output Frequency (50Hz/100Hz/200Hz/400Hz). 

The chosen output frequency is recommended no more than the maximum servo supported frequency. 

 

Notices: 

If  you  open  the  gimbal  control  in  assistant  software  during  the  configuration,  please  note  that  there  are 

outputs  from  F1  and  F2  ports.  You  should  never  connect  these  ports  to  ESCs  which  are  wired  with 

propellers and motors. 

Tips: 

NAZA supports servo center 1520us. 

 

 

STEP2:  Servo Travel Limit 

Range: -1000 to+1000 

MAX

/

MIN  are  servo  travel  limits;  adjust  them  to  avoid  mechanical  binding;  Place  your  multi-rotor  on  level 

ground, adjust Center value of Pitch and Roll direction to make the camera mounting frame to your desired 

angle-to-ground.

   

 

 

 

Summary of Contents for Naza












































Reviews:

No comments