DINA Elektronik DBDS 1VMG, Product Information

Page: 9 / 32

Product Information
Safety technics modular generation in metal housing version 08 dated: 2009-04-10 page 9 from 32
Function of the inputs of DNDS 1EG V7C with the item-no. 22EG36-01
The monitoring frequencies of the tool setting mode (mode 2) must be selected via the D-inputs. The selection will
be done, if the D-inputs will be connected to 24V. During the Mode 2 the SH-input has to be connected to 24V.
The Function of the MT- and R1-input is the same as with
DNDS 1EG V7C,
item-no
22EG36
Adjusting table DNDS 1EG V7C item-no 22EG36-01
R1 Table
:
Selection of the monitoring frequencies
via the DIP switches S3 and S5 for semi automatic
D-Table : Selection of the monitoring frequencies for the SH-input via D1-D6.
The SH-input has to be connected to 24V.
Switch positions Switch positions
of S3 and S5 of S3 and S5
R1 Position = ON R1 Position = ON D-inputs connected to 24V D-inputs connected to 24V
Hz 1 2 3 4 5 6 Hz 1 2 3 4 5 6 D1 D2 D3 D4 D5 D6 Hz D1 D2 D3 D4 D5 D6 Hz
00 125 32 600 00 2 32 7,5
01 600 33 440 01 4 33 7,5
02 50 34 125 02 5 34 7,5
03 240 35 312 03 6 35 7,5
04 100 36 469 04 8 36 7,5
05 75 37 140 05 10 37 7,5
06 312 38 350 06 12 38 7,5
07 500 39 525 07 14 39 7,5
08 40 155 08 16 40 7,5
09 41 387 09 18 41 7,5
10 20 42 581 10 20 42 7,5
11 50 43 180 11 22 43 7,5
12 125 44 450 12 24 44 7,5
13 240 45 200 13 26 45 7,5
14 40 46 500 14 28 46 7,5
15 100 47 15 30 47 7,5
16 250 48 300 16 32 48 7,5
17 480 49 17 34 49 7,5
18 65 50 360 18 36 50 7,5
19 162 51 19 38 51 7,5
20 325 52 420 20 40 52 7,5
21 487 53 21 45 53 7,5
22 80 54 22 50 54 7,5
23 200 55 23 60 55 7,5
24 400 56 24 70 56 7,5
25 600 57 25 80 57 7,5
26 95 58 21 26 90 58 7,5
27 237 59 12 27 100 59 7,5
28 475 60 17 28 125 60 7,5
29 110 61 25 29 150 61 7,5
30 275 62 38 30 180 62 7,5
31 550 63 31 225 63 7,5
Outputs of DNDS 1EG V7C item-no 22EG36-01
The modules DNDS 1EG V3C has two positive switching outputs O1 and O2. Normally the outputs are switched to
24V. The power supply for these outputs has to be connected to the terminal 24V at the module.
Output O1 switch off, if there is a sensors failure at the Encoder input or at IN1 or IN2.
O1 switch on again, if the reason for the switching off does not exist.
Output O2 switch off and the LED SPEED is not illuminated, if there is an overspeed, an external or an internal
failure, that causes a switch off of the outputs at the output modules.
O2 with overspeed:
O2 switch on again, if the actual speed is
≥ ≥ ≥ ≥
10% less than the selected speed. The LED SPEED is illuminated.
The function of O2 is independent in an enabled or disabled speed output automatic restart