background image

5.1   Route OPSW’s ................................................................17
5.2  Setting up Routes using the EZ RTS button................................17
5.3  DT602 Reading and Editing  routes ..............................18

6.0   Booster Operations (OPS) Mode read-back ....................18
7.0  How the Manages Addresses ............................................19

7.1  Purging of addresses .....................................................................19

8.0  Connecting the to a Computer ..........................................19

8.1  Driver Installation............................................................................19
8.2  Hardware Installation......................................................................19
8.3  Software Installation .......................................................................20
8.4  Connecting the to a Computer Additional Troubleshooting .20

9.0  IPL Updating the to the latest firmware   .........................20
FCC Information .........................................................................................21
Warranty and Repair Information .............................................................22

Summary of Contents for DCS240

























Reviews: