manualshive.com logo in svg

Diamond SmartLyte, Service Manual

Share
Download
Diamond SmartLyte Service Manual Download Page 50

 

 

 

4 Description of Modules 

                                                                            

ECO 9085 SOP05-5038F Rev.05 Effective Date: 12/06/18  Page 50 of 81

 

 

Temperature Sensor circuit 

 

This circuit creates a temperature –depended voltage which is converted by software to 

degree C. R190 can be adjusted to correct temperature setting.  

 

Analog Channel and A/D Converter 

 

 The analog inputs from the amplifiers are connected to IC U21 and U22 ADC1 and 

ADC2 converters. ADC 2 is in the schematic for future developments.  

 

JP Connector explanation in the CPU board. 

 

In order to fulfill all responsibilities of the CPU board and the program installed on it, is 

equipped with a number of connectors to interface it with all peripherals. The description 

of the JP connectors is as below: 

 

JP1 - Graphic printer connector 

JP2- NA 

JP3 - Power connector receptacle. 

JP4 - Display connector 

JP5 – Valve board connector 

JP6- NA 

JP7 – Serial DB9 RS232 Connector 

JP8 – USB1 Connector 

JP9 – USB 2 Connector 

JP10- RFID connector 

JP11- JTAG connector 

 

4.3.2.

 

Valve  Board CN-A4018 

 

The valve board contains the LED array used to illuminate the measuring chamber and 

the interconnectors used for all solenoids, the peristaltic pump and the door sensor. A 

ribbon cable from the CPU  Board supplies the electrical connection for each signal 

through connector JP5. 

 

4.3.3.

 

Display Board CN-A4017/CN-A4059 

 

The graphic display module TH16032A  has  a 160x32  resolution. The  backlight is 

adjustable and allows for changing the contrast. In the same board are all connection for 

YES and NO buttons as well sample sensor and temperature sensor. The connection of 

the display board with CPU board is done through ribbon cable connected to JP4 in the 

CPU board. The new display board is equipped with two potentiometers for controlling 

the backlight and the contrast in the display. 

  

Note: Graphics Display is not compatible as a direct replacement with previous 

generation. 

 

Summary of Contents for SmartLyte


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands