manualshive.com logo in svg

Diamond SmartLyte, Service Manual, Page: 2 / 81

Share
Download
Diamond SmartLyte Service Manual Download Page 2

 

                                                                            

ECO 9085 SOP05-5038F Rev.05 Effective Date: 12/06/18  Page 2 of 81

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SMARTLYTE ELECTROLYTE ANALYZER is a Registered Trademark of Diamond Diagnostics Inc. 

 

The Diamond Diagnostics SMARTLYTE analyzer is for In Vitro Diagnostic use.  

 

Diamond Diagnostics Inc  

333 Fiske Street  

Holliston, MA 01746  

 

Diamond Diagnostics Kft 

Óradna Street 6 

1044 Budapest Hungary 

 

 

2009 SMARTLYTE ELECTROLYTE ANALYZER. All

 

rights reserved. 

Registered in the United States Patent and Trademark Office 

 

The information in this manual was correct at the time of printing.   However, Diamond 

Diagnostics Inc continues to improve products and reserves the right to change the 

specifications, equipment, and maintenance procedures at any time without notice.  

 

If the system is used in a manner differently than specified by Diamond Diagnostics Inc., the 

protection provided by the equipment may be impaired. See warning and hazard statements.  

 

 

 

Summary of Contents for SmartLyte


















































































Reviews:

No comments