Dewert duomat 7 care l Installation Instructions Manual Download Page 20

20

9.

Cleaning

10.

Disposal

The

drive system has been designed to facilitate cleaning for the user, and this

has been made even easier thanks to the large number of flat surfaces.
The

drive system should be cleaned with a proprietary cleaning agent suitable for

using a damp cloth. Always note the instructions provided by the manufacturer of

the respective cleaning agent used.

the drive system in a wash tunnel or with a

. You risk damaging the equipment!

When

take care not to damage the drive system’s

!

The drive system only offers protection against spray water (classification IP44).

such as

,

or similar substances.

The

drive system contains electronic components, cables, metal, plastic etc.

:

DUOMAT 7

DUOMAT 7

polyamid 6

Never clean

high-pressure cleaner nor spray

liquids onto it

cleaning

mains connection lead

Do not use any solvents

benzene alcohol

DUOMAT 7

Before cleaning, always pull out the mains plug!

The

drive system should be disposed of in accordance with the environmental

regulations applicable in the respective country. Information on this subject can also be
obtained from

Federal Association for
Disposal Management BDE
Behrenstraße 29
D-10117 Berlin
Germany
Phone: +49 (0) 30-59 00 33 5-0
www.bde-berlin.de

are to be disposed of in line with the

.

DUOMAT 7

Accumulators

AltBattVO

Drive systems and accumulators may not be disposed of with
the normal household waste! (Ordinance on Disposal of Old Batteries).

Notes on environmental directives and legislation

"

"

The product is not subject to the European Directive 2002 / 96 / EC (WEEE) and its
amendment EU Directive 2003 / 108 / EC.

In as far as this product includes batteries, this complies with

the Battery Ordinance of 27th March 1998 (BGBI. I S.658)

"

The product complies with the European Directive 2002 / 95 / EC (RoHS as of
01.07.2006).

DUOMAT 7 CARE L/HOSP L

Summary of Contents for duomat 7 care l


























Reviews: