DETEWE opencom 100 Mounting And Commissioning Manual Download Page 46

Page: 46 / 136

Mounting the OpenCom 110/120 Rack InfoCom System

Pinning of RJ 45 Jacks

Switches on Front Panel

■

The bus termination resistors
for all the S

internal ports are

switchable.

Please note:

In the factory set-

ting on delivery, the switches are
open, i.e. the termination resistors are
not switched on.

■

The internal S

bus is terminated

at one end (NT) by the
OpenCom 110/120 Rack with
100

Ω

termination resistors; the

DIP switches below the respec-
tive RJ jacks are “on” (i.e. closed)
in the upper position.

Please note:

Both S

bus

switches must be in the same posi-
tion.

■

The S

bus is terminated at both

ends with 100

Ω

termination re-

sistors; the DIP switches below
the respective RJ jacks are “off”
(i.e. open) in the lower position.

■

The DIP switches on a/b port 1
are normally “on” (i.e. closed) in
the upper position. If the device
is set for the entrance intercom
port, the switches must be in the
lower position (“off”).

Scope of Delivery

■

Adapter cable RJ 45 - RS 232 for
V.24/COM interface

■

Screws for rack mounting

■

For complete installation the
country-specific installation
package is necessary. It contains
the power cord, a complete set
of manuals and a CD-ROM.

Note:

Note for the DeTeWe in-

staller: Please download and install
the latest released software from our
Web site/partnership area.

, a/b, Sensor,

Actor

PIN 4-5

PIN 4-5, 3-6

PIN 4-5, 1-2

10Base-T

PIN 1-2, 3-6

Summary of Contents for opencom 100









































































































































Search results

Summary of Contents for opencom 100

Reviews:

Related manuals for opencom 100

Brands by name

Popular brands

DETEWE opencom 100, Mounting And Commissioning Manual

Search results

Summary of Contents for opencom 100

Reviews:

Related manuals for opencom 100

Brands by name

Popular brands