manualshive.com logo in svg

Dell Vostro 3580, Service Manual

Share
Download
Dell Vostro 3580 Service Manual Download Page 78

Next steps

1. Replace the 

camera

2. Replace the 

display bezel

3. Replace the 

display assembly

4. Replace the 

hard drive assembly

5. Replace the 

system fan

6. Replace the 

heatsink

7. Replace the 

SSD

8. Replace the 

WLAN

9. Replace the 

battery

10. Replace the 

base cover

11. Replace the 

optical drive assembly

12. Replace the 

SD memory card

13. Follow the procedure in 

after working inside your computer

Display hinges

Removing the display hinges

Prerequisites

1. Follow the procedure in 

before working inside your computer

2. Remove the 

SD memory card

3. Remove the 

optical drive assembly

4. Remove the 

base cover

5. Remove the 

battery

6. Remove the 

WLAN

7. Remove the 

SSD

8. Remove the 

hard drive assembly

9. Remove the 

system fan

10. Remove the 

heatsink

11. Remove the 

display assembly

12. Remove the 

display bezel

13. Remove the 

camera

14. Remove the 

display panel

Steps

1. Remove the eight (M2.5x2.5) screws and two (M2x2) screws that secure the hinges to the display back-cover and antenna assembly 

[1, 2].

2. Lift the hinges and brackets off the display back-cover and antenna assembly [3].

78

Removing and installing components

Summary of Contents for Vostro 3580



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands