manualshive.com logo in svg

Dell Vostro 3580, Service Manual

Share
Download
Dell Vostro 3580 Service Manual Download Page 59

Installing the power button board

Steps

1. Place the power-button board into the slot on the palmrest and keyboard assembly [1].
2. Replace the single (M2x2) screw that secures the power button board to the palmrest and keyboard assembly [2].
3. Affix the conductive tape to the power button board [3].
4. Slide the power button cable to the system board and close the latch to secure the cable [4].

Next steps

1. Replace the 

display assembly

2. Replace the 

system fan

3. Replace the 

WLAN

4. Connect the battery cable to the connector on the system board.
5. Replace the 

base cover

6. Replace the 

optical drive assembly

7. Replace the 

SD memory card

8. Follow the procedure in 

after working inside your computer

System board

Removing the system board

Prerequisites

1. Follow the procedure in 

before working inside your computer

2. Remove the 

SD memory card

3. Remove the 

base cover

4. Remove the 

battery

Removing and installing components

59

Summary of Contents for Vostro 3580



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands