manualshive.com logo in svg

Dell Vostro 3580, Service Manual

Share
Download
Dell Vostro 3580 Service Manual Download Page 41

4. Replace the 

SD memory card

5. Follow the procedure in 

after working inside your computer

Heat sink

Removing the heatsink

Prerequisites

1. Follow the procedure in 

before working inside your computer

2. Remove the 

SD memory card

3. Remove the 

optical drive assembly

4. Remove the 

base cover

5. Disconnect the battery cable from the connector on the system board.

Steps

1. Loosen the four captive screws that secure the heatsink to the system board [1].

NOTE: 

Loosen the screws in the order of the callout numbers [1, 2, 3, 4] as indicated on the heatsink.

2. Remove the three (M2x3) screws that secure the heatsink to the system board [2].
3. Lift the heatsink off the system board [3].

Installing the heatsink

Steps

1. Place the heatsink on the system board and align the screw holes on the heatsink with the screw holes on the system board [1].

Removing and installing components

41

Summary of Contents for Vostro 3580



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands