manualshive.com logo in svg

Dell Vostro 3580, Service Manual

Share
Download
Dell Vostro 3580 Service Manual Download Page 66

Next steps

1. Replace the 

display assembly

2. Replace the 

heatsink

3. Replace the 

system fan

4. Replace the 

SSD

5. Replace the 

WLAN

6. Replace the 

memory

7. Replace the 

battery

8. Replace the 

base cover

9. Replace the 

SD memory card

10. Follow the procedure in 

after working inside your computer

Power button

Removing the power button with fingerprint reader

Prerequisites

1. Follow the procedure in 

before working inside your computer

2. Remove the 

SD memory card

3. Remove the 

optical drive assembly

4. Remove the 

base cover

5. Remove the 

battery

6. Remove the 

WLAN

7. Remove the 

SSD

8. Remove the 

system fan

9. Remove the 

heatsink

10. Remove the 

display assembly

11. Remove the 

power button board

12. Remove the 

system board

Steps

1. Remove the single (M2x2) screw that secures the power button on the palmrest and keyboard assembly [1].
2. Lift the power button with fingerprint reader board off the palmrest and keyboard assembly [2].
3. Peel the fingerprint reader cable off the palmrest and keyboard assembly.

66

Removing and installing components

Summary of Contents for Vostro 3580



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands