manualshive.com logo in svg

Dell Vostro 3580, Service Manual

Share
Download
Dell Vostro 3580 Service Manual Download Page 23

NOTE: 

If you do not hear the click, remove the memory module and reinstall it.

Next steps

1. Connect the 

battery

 cable to the connector on the system board.

2. Replace the 

base cover

3. Replace the 

optical drive assembly

4. Replace the 

SD memory card

5. Follow the procedure in 

after working inside your computer

WLAN card

Removing the WLAN card

Prerequisites

1. Follow the procedure in 

before working inside your computer

2. Remove the 

SD memory card

3. Remove the 

optical drive assembly

4. Remove the 

base cover

5. Disconnect the 

battery

 cable from the connector on the system board.

Steps

1. Remove the single (M2x3) screw that secures the WLAN card bracket to the system board [1].
2. Slide and remove the WLAN card bracket that secures the WLAN cables [2].
3. Disconnect the WLAN cables from the connectors on the WLAN card [3].
4. Lift the WLAN card away from the connector [4].

Removing and installing components

23

Summary of Contents for Vostro 3580



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands