Dell Vostro 3580 Service Manual Download Page 42

Page: 42 / 90

2. Replace the three (M2x3) screws that secure the heatsink to the system board [2].
3. In sequential order (as indicated on the heatsink), tighten the four captive screws that secure the heatsink to the system board [3].

Next steps

1. Connect the battery cable to the connector on the system board.
2. Replace the

base cover

3. Replace the

optical drive assembly

4. Replace the

SD memory card

5. Follow the procedure in

after working inside your computer

VGA Daughterboard

Removing the VGAcable

Prerequisites

1. Follow the procedure in

before working inside your computer

2. Remove the

SD memory card

3. Remove the

optical drive assembly

4. Remove the

base cover

5. Disconnect the battery cable from the connector on the system board.
6. Remove the

7. Remove the

8. Remove the

9. Remove the

10. Remove the

11. Remove the

12. Remove the

Removing and installing components

Summary of Contents for Vostro 3580



























































































Search results

Summary of Contents for Vostro 3580

Reviews:

Brands by name

Popular brands

Dell Vostro 3580, Service Manual

Search results

Summary of Contents for Vostro 3580

Reviews:

Brands by name

Popular brands