Dell S4048T-ON Configuration Manual Download Page 228 | Manualshive

Page: 228 / 1146

background image

ffffffff ffffffff ffffffff ffffffff 00130400

PDU[3] : len 19, captured 00:34:51 ago

ffffffff ffffffff ffffffff ffffffff 00130400

PDU[4] : len 19, captured 00:34:22 ago

ffffffff ffffffff ffffffff ffffffff 00130400

[. . .]

Outgoing packet capture enabled for BGP neighbor 20.20.20.2

Available buffer size 40958758, 27 packet(s) captured using 562 bytes

PDU[1] : len 41, captured 00:34:52 ago

ffffffff ffffffff ffffffff ffffffff 00290104 000100b4 14141401 0c020a01 04000100 01020080

00000000

PDU[2] : len 19, captured 00:34:51 ago

ffffffff ffffffff ffffffff ffffffff 00130400

PDU[3] : len 19, captured 00:34:50 ago

ffffffff ffffffff ffffffff ffffffff 00130400

PDU[4] : len 19, captured 00:34:20 ago

ffffffff ffffffff ffffffff ffffffff 00130400

[. . .]

The following example shows how to view space requirements for storing all the PDUs. With full internet feed (205K) captured,
approximately 11.8MB is required to store all of the PDUs.

Dell(conf-router_bgp)#do show capture bgp-pdu neighbor 172.30.1.250

Incoming packet capture enabled for BGP neighbor 172.30.1.250

Available buffer size 29165743, 192991 packet(s) captured using

11794257 bytes

[. . .]

Dell(conf-router_bgp)#do sho ip bg s

BGP router identifier 172.30.1.56, local AS number 65056

BGP table version is 313511, main routing table version 313511

207896 network entrie(s) and 207896 paths using 42364576 bytes of memory

59913 BGP path attribute entrie(s) using 2875872 bytes of memory

59910 BGP AS-PATH entrie(s) using 2679698 bytes of memory

3 BGP community entrie(s) using 81 bytes of memory

Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/Pfx

1.1.1.2 2 17 18966 0 0 0 00:08:19 Active

172.30.1.250 18508 243295 25 313511 0 0 00:12:46 207896

PDU Counters

Dell Networking OS supports additional counters for various types of PDUs sent and received from neighbors.

These are seen in the output of the

show ip bgp neighbor

command.

Sample Configurations

The following example configurations show how to enable BGP and set up some peer groups. These examples are not comprehensive
directions. They are intended to give you some guidance with typical configurations.

To support your own IP addresses, interfaces, names, and so on, you can copy and paste from these examples to your CLI. Be sure that you
make the necessary changes.

The following illustration shows the configurations described on the following examples. These configurations show how to create BGP
areas using physical and virtual links. They include setting up the interfaces and peers groups with each other.

Figure 24. Sample Configurations

228

Border Gateway Protocol IPv4 (BGPv4)

«
...
226
227
228
229
230
...
»

Summary of Contents for S4048T-ON



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S4048T-ON

Brand: 4IPNET Pages: 97

Brand: BandLuxe Pages: 67

NJ220 - IntelliJack Switch

Brand: 3Com Pages: 82

Conel UR5i v2 Libratum

Brand: B&B Electronics Pages: 32

Brand: ROE Pages: 41

Brand: hilscher Pages: 154

Brand: T.A Pages: 11

Brand: ICP DAS USA Pages: 8

Brand: Xtreme Pages: 83

i.LON SmartServer

Brand: Echelon Pages: 34

Brand: Altimium Pages: 12

Security Router X-PeditionTM

Brand: Enterasys Pages: 466

Brand: Edge-Core Pages: 64

Brand: ADTRAN Pages: 136

MTDOT-868 Series

Brand: Multitech Pages: 60

Brand: Vivotek Pages: 317

EZ-KIT LITE ADSP-2191

Brand: Analog Devices Pages: 98

cPCI-3520 Series

Brand: ADLINK Technology Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands