Example of Viewing Session Parameters
R1(conf-if-te-4/24)#bfd interval 100 min_rx 100 multiplier 4 role passive
R1(conf-if-te-4/24)#do show bfd neighbors detail
Session Discriminator: 1
Neighbor Discriminator: 1
Local Addr: 2.2.2.1
Local MAC Addr: 00:01:e8:09:c3:e5
Remote Addr: 2.2.2.2
Remote MAC Addr: 00:01:e8:06:95:a2
Int: TenGigabitEthernet 4/24
State: Up
Configured parameters:
TX: 100ms, RX: 100ms, Multiplier: 4
Neighbor parameters:
TX: 100ms, RX: 100ms, Multiplier: 3
Actual parameters:
TX: 100ms, RX: 100ms, Multiplier: 4
Role:
Passive
Delete session on Down: False
Client Registered: CLI
Uptime: 00:09:06
Statistics:
Number of packets received from neighbor: 4092
Number of packets sent to neighbor: 4093
Number of state changes: 1
Number of messages from IFA about port state change: 0
Number of messages communicated b/w Manager and Agent: 7
Disabling and Re-Enabling BFD
BFD is enabled on all interfaces by default, though sessions are not created unless explicitly configured.
If you disable BFD, all of the sessions on that interface are placed in an Administratively Down state ( the first message example), and the
remote systems are notified of the session state change (the second message example).
To disable and re-enable BFD on an interface, use the following commands.
•
Disable BFD on an interface.
INTERFACE mode
no bfd enable
•
Enable BFD on an interface.
INTERFACE mode
bfd enable
If you disable BFD on a local interface, this message displays:
R1(conf-if-te-4/24)#01:00:52: %RPM0-P:RP2 %BFDMGR-1-BFD_STATE_CHANGE: Changed session
state to
Ad
Dn
for neighbor 2.2.2.2 on interface Te 4/24 (diag: 0)
If the remote system state changes due to the local state administration being down, this message displays:
R2>01:32:53: %RPM0-P:RP2 %BFDMGR-1-BFD_STATE_CHANGE: Changed session state to
Down
for
neighbor
2.2.2.1 on interface Te 2/1 (diag: 7)
Configure BFD for Static Routes
BFD offers systems a link state detection mechanism for static routes. With BFD, systems are notified to remove static routes from the
routing table as soon as the link state change occurs, rather than waiting until packets fail to reach their next hop.
Bidirectional Forwarding Detection (BFD)
151
Summary of Contents for S4048T-ON
