Dell PowerVault DR4100 Owner'S Manual Download Page 77 | Manualshive

Page: 77 / 122

background image

Installing The Hard-Drive Backplane (Back)

CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.

1.

Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2.

Open the system.

3.

Align the notches on the backplane with the notches on the chassis.

4.

Lift the release pin and slide the backplane on the chassis until firmly seated.

5.

Release the release pin to lock the backplane to the chassis.

6.

Reconnect all the cables to the backplane.

7.

Install both the hard drives in their original location.

8.

Close the system.

9.

Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

I/O Panel

Removing The I/O Panel

CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.

1.

If installed, remove the front bezel.

2.

Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and

peripherals.

3.

Open the system.

CAUTION: To prevent damage to the I/O cable, you must release the locking tab before removing or installing
the I/O cable from the connector on the hard-drive backplane.

4.

Rotate the locking tab on the I/O cable connector clockwise 90 degrees to release the lock.

5.

Disconnect the I/O cable from the backplane.

6.

Remove the three Torx screws securing the I/O panel to the chassis.

7.

Pull out the I/O panel cable through the channel on the chassis.

77

«
...
75
76
77
78
79
...
»

Summary of Contents for PowerVault DR4100



























































































































Reviews:

No comments

Related manuals for PowerVault DR4100

Brand: IBM Pages: 214

SAT-IP EXIP 418

Brand: Kathrein Pages: 16

Brand: BRONKHORST Pages: 19

Brand: NASdeluxe Pages: 6

Brand: Rasilient Pages: 30

Brand: TAG Pages: 84

Brand: Promise Technology Pages: 324

Brand: Measy Pages: 15

IMS-LANTIME M500

Brand: Meinberg Pages: 162

GV-Storage System

Brand: GeoVision Pages: 9

Brand: W&T Pages: 79

326m - eServer - 7969

Brand: IBM Pages: 82

Brand: VVDN Technologies Pages: 35

Brand: Lantronix Pages: 92

Brand: Fiery Pages: 160

Brand: Aimetis Pages: 16

Brand: Inspur Pages: 100

Brand: Oracle Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands