Dell PowerVault DR4100 Owner'S Manual Download Page 71 | Manualshive

Page: 71 / 122

background image

Figure 37. Removing and Installing the Power Supply Blank

1. power supply blank

Installing The Power Supply Blank

NOTE: Install the power supply blank only in the second power supply bay.

To install the power supply blank, align the blank with the power supply bay and insert it into the chassis until it clicks
into place.

System Battery

Replacing The System Battery

WARNING: There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with
the same or equivalent type recommended by the manufacturer. See your safety information for additional
information.

CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.

1.

Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and

peripherals.

2.

Open the system.

3.

Remove the cooling shroud.

4.

Locate the battery socket.

CAUTION: To avoid damage to the battery connector, you must firmly support the connector while installing or
removing a battery.

5.

To remove the battery, support the battery connector by pressing down firmly on the positive side of the connector.

71

«
...
69
70
71
72
73
...
»

Summary of Contents for PowerVault DR4100



























































































































Reviews:

No comments

Related manuals for PowerVault DR4100

Brand: HPE Pages: 174

Brand: AC&T System Pages: 32

Brand: Advantech Pages: 43

PRICOM PRICOM C- 5100

Brand: Silex technology Pages: 7

Brand: Speco Pages: 28

Brand: Olive Pages: 24

xSeries 440 8687

Brand: IBM Pages: 80

xSeries 230 6RY

Brand: IBM Pages: 194

SIGMABLADE AD106a

Brand: NEC Pages: 2

Series3800/S120R-2

Brand: NEC Pages: 2

Series3800/S120R-1

Brand: NEC Pages: 3

Series3800/S110R-1

Brand: NEC Pages: 2

ServerCare Express5800/FT

Brand: NEC Pages: 14

Brand: NEC Pages: 19

NEC Express5800/B120d

Brand: NEC Pages: 22

NEAX2000 ND-91649

Brand: NEC Pages: 58

Brand: NEC Pages: 106

NX7700i/5040H-32

Brand: NEC Pages: 170

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands