Dell PowerVault DR4100 Owner'S Manual Download Page 27

Page: 27 / 122

iDRAC Settings Utility

The iDRAC Settings utility is an interface to setup and configure the iDRAC parameters using UEFI. You can enable or
disable various iDRAC parameters using the iDRAC Settings utility.

NOTE: Accessing some of the features on the iDRAC Settings utility requires the iDRAC7 Enterprise License
upgrade.

For more information on using iDRAC, see the

iDRAC7 User's Guide

under Software

→

Systems Management

→

Dell

Remote Access Controllers, at dell.com/support/manuals.

Entering The iDRAC Settings Utility

Turn on or restart the managed system.

Press <F2> during Power-on Self-test (POST).

In the System Setup Main Menu page, click iDRAC Settings.
The iDRAC Settings screen is displayed.

Summary of Contents for PowerVault DR4100



























































































































Search results

Summary of Contents for PowerVault DR4100

Reviews:

Related manuals for PowerVault DR4100

Brands by name

Popular brands

Dell PowerVault DR4100, Owner'S Manual

Search results

Summary of Contents for PowerVault DR4100

Reviews:

Related manuals for PowerVault DR4100

Brands by name

Popular brands