Dell PowerVault DR4100 Owner'S Manual Download Page 60

Page: 60 / 122

Remove the expansion-card riser 3 and any card(s) installed in the riser.

Locate the internal dual SD module installed on the J_IDSDM connector on the system board.

If applicable, remove the SD card(s).

Holding the tab, pull the dual SD module to remove it from the system board.

Replace the expansion-card riser 3 and if applicable, replace the card(s) in the riser.

Close the system.

Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

Figure 30. Removing and Installing the Internal Dual SD Module

1. blue pull tab
2. SD card 1
3. SD card 2

4. dual SD module
5. connector on the system board

Summary of Contents for PowerVault DR4100



























































































































Search results

Summary of Contents for PowerVault DR4100

Reviews:

Related manuals for PowerVault DR4100

Brands by name

Popular brands

Dell PowerVault DR4100, Owner'S Manual

Search results

Summary of Contents for PowerVault DR4100

Reviews:

Related manuals for PowerVault DR4100

Brands by name

Popular brands